Job Title

Job Summary The Associate Manager Technical Services is responsible for providing end-to-end technical and engineering support across manufacturing operations, projects, and technology transfer activities. The role involves process engineering, scale-up, equipment selection, capacity analysis, debottlenecking, and ensuring safe, efficient, and compliant plant operations. The position acts as a key interface between R&D, Manufacturing, Quality, Projects, EHS, and external vendors.Key Responsibilities1. Process Engineering & Manufacturing SupportProvide technical support to manufacturing operations to ensure consistent, safe, and efficient production. Review and optimize process parameters to improve yield, quality, throughput, and cost efficiency. Develop, review, and maintainProcess Flow Diagrams (PFDs)andPiping & Instrumentation Diagrams (P&IDs) . Performmaterial and energy balance calculations . Support troubleshooting of process deviations, failures, and operational challenges.2. Technology Transfer & Scale-UpLead and supporttechnology transferfrom R&D / pilot scale to commercial manufacturing. Translate laboratory and pilot data into scalable and robust manufacturing processes. Prepare and reviewtechnology transfer protocols, reports, and process descriptions . Coordinate trial runs, scale-up batches, and validation activities. Ensure process knowledge management and documentation during transfers.3. Equipment Selection & Design ReviewDefineUser Requirement Specifications (URS)for process equipment. Evaluate, select, and technically approve equipment and vendors. ReviewGeneral Arrangement (GA) drawings , layout plans, and equipment datasheets. Ensure equipment design complies with process, GMP, safety, and ergonomic requirements. Support FAT, SAT, commissioning, and qualification activities.4. Capacity Calculation & DebottleneckingPerformcapacity assessment and throughput analysisfor existing and new facilities. Identify bottlenecks across unit operations and utilities. Propose and implementdebottlenecking solutionsincluding process optimization, equipment upgrades, or layout modifications. Support expansion and brownfield/greenfield project planning.5. Engineering Calculations & Technical StudiesPerform and review engineering calculations, including: Flow rate, residence time, and heat transfer calculations Equipment sizing (reactors, mixers, dryers, filters, pumps, heat exchangers) Utility requirements (steam, water, compressed air, HVAC, power) Support preparation ofbasic engineering packagesand design inputs.6. Instrumentation & Automation InterfaceReview and defineinstrumentation philosophy , control schemes, and interlocks. Support selection of sensors, control valves, transmitters, and analytical instruments. Review automation narratives, logic diagrams, and alarm philosophies. Coordinate with automation and electrical teams for DCS/PLC integration.7. Process Safety & ComplianceParticipate inprocess safety studiessuch as HAZOP, HAZID, What-If, and risk assessments. Ensure compliance withEHS, GMP, regulatory, and statutory requirements . Support development and review of SOPs, safety interlocks, and emergency procedures. Ensure safe design practices related to pressure systems, hazardous materials, and utilities.8. Project Support & Cross-Functional CoordinationProvide technical inputs during project planning, execution, and commissioning. Coordinate with Quality, Validation, EHS, Maintenance, and Production teams. Support change management activities (MOC) related to process and equipment changes. Manage technical documentation and ensure traceability. 9. Documentation & Continuous ImprovementPrepare and review technical documents including: Process descriptions and design basis documents Equipment specifications and datasheets Validation support documents Drive continuous improvement initiatives using Lean, Six Sigma, or similar methodologies. Support audits and regulatory inspections with technical inputs.Required QualificationsEducationBachelor’s degree inChemical Engineering, Process Engineering , or related discipline Certified Project Management preferred.Experience8–12 years of relevant experience intechnical services, process engineering, manufacturing, or projects Experience in regulated manufacturing environments (LIB,E waste, Pharma, API, Biotech, Chemicals, Food) preferredKey Skills & CompetenciesTechnical SkillsStrong knowledge ofprocess engineering principles Expertise inPFDs, P&IDs, GA drawings , and engineering documentation Hands-on experience withtechnology transfer and scale-up Proficiency incapacity calculation and debottlenecking Equipment selection and specification expertise Understanding ofinstrumentation, automation, and control systems Process safety and risk assessment knowledgeSoftware & ToolsAspen / HYSYS / ChemCAD (preferred) MS Excel (advanced engineering calculations) ERP / Documentation systems (as applicable)Behavioural& Leadership SkillsStrong analytical and problem-solving skills Effective communication and stakeholder management Ability to lead cross-functional teams and technical discussions Structured approach to documentation and compliance Continuous improvement mindsetWork EnvironmentManufacturing plant, corporate engineering, or project sites May require travel for project execution, vendor inspections, or technology transfer